What’s New?

It’s been a while since I posted anything on this blog, too long! But there’s not been much happening with the bikes as they’ve been running well. However I’m feeling in need of a change now so –.

I’ve taken the sidecar off the big Panther, not the easiest of jobs when working on your own, but do-able, the body is now up on a pair of trestles in the shed and the chassis is in the back yard.

The Panther now stands as a solo in the garage, but she’s not on her own as the old BMW has been brought out of storage and is standing beside her, they make a good pairing, the 600cc 1937 Panther M100 and the 750cc 1940 BMW R12.

Although the Panther has the smaller displacement engine of the two she is the more powerful at 26bhp to the BMW’s 20bhp, but the BMW is a twin cylinder side-valve with a heavy external flywheel so is possibly the better slogger of the two, still neither was intended as a sports bike.

Anyway the BMW is set up with a full set of Steib quick release sidecar fittings so once I have the chair set up for her I can drop it on and off in around five minutes work, useful!!

Now, what does the BMW need doing to get her in commission again?

Well her battery is an AGM sealed unit and has survived her spell in the storage unit. It was still showing about half-charged when I put it on the charger. She is magneto ignition and that’s sparking well but I’ll treat her to a new pair of plugs.

How about oils?, well oil is cheaper than metal so it’s new oil all round, and owing to her age it’s an old-fashioned non-detergent type oil. Equally I needed new drain and filler plug gaskets.

On a machine of this age these should be the hollow rolled-copper type rather than the solid aluminium ones BMW now supply. A quick rake round on ebay soon found a supplier of these in the necessary 14mm and 18mm sizes.

Rather than run her up to hot on the old oil I let her drain out overnight and then it was just a case of fill the engine to between marks on the dip-stick, fill the gearbox and final drive until the oil reached the bottom of the filler hole threads and that was that.

Now the acid test! I put a half-gallon of fuel into the tank, no leaks visible! GOOD!!, turn on the tap (which way is “ON” and which is “RESERVE”??, I can’t remember!! ).

OK, the carbs filled up so a good tickle on each carb, crack open the throttle and turn over the engine several times to prime the cylinders, then it was just switch on the ignition and kick her over.

While she fired she didn’t pick up so a tad more throttle and try again and the old girl was running again! Tick-over balance is a bit off but I’ll need her warmed through to set that up so it will have to wait.

Now I know she’s a runner what else needs doing.

An immediate obvious is indicators!. Last time out she was hauling the chair.

I know it’s non-original, but on modern roads an outfit NEEDS indicators and now you can use LED units without overloading the electrical system so she was fitted up with lights on one side, the others being on the chair. So it’s get another pair of indicators and fit them.

I had to make up (and paint) a set of mounting brackets for them, run in the wiring and then tap it into the circuit to the sidecar indicators, a quick check and they were working..

Next thing was cosmetics, the front mudguard needed some serious touch-up where the paint has been badly scarred and had started lifting while the old lady had been in the storage unit.

Fortunately it can be redone while still on then bike as it would be serious hassle to remove it and then a dose of “T-Cut” after about a fortnight’s curing and then a polish job should see things OK.

As I’m writing this she’s standing in the garage with the first top coat on the guard giving it time to harden off before she’s put away for the night, another coat tomorrow should then see it ok.

I can’t really complain as both guards were in a bad state when I got the bike back at the beginning of the Eighties and they needed serious patching to be made usable, and she has seen some serious mileage since then!

= = = = = = = = = = = = = = = = =

When I had a look at things the next day I was very happy as to the finish, the “Craftsman” paint I was trying out as a replacement for my old favourite “Tekaloid” came through with flying colours.

Only trouble was the contrast with the old paint, this had weathered over time so the new paint stood out like the proverbial on a barn door!.

So I broke out the “T-Cut” and gave the guard a good rub down and that did the trick, you no longer noticed the repair unless you looked closely, snag is I now have to do the rest of the bike to get it to match the front mudguard!.

The R12 is quite heavily pinstriped so this repair has left a gap in the lining on the front guard that I’ll need to patch, so I now need to break out the lining brushes.

Lining is properly done free-hand and the difficult bit is getting a tight curve without smearing. My way round this is to mask out the line so that any smear goes onto the masking tape, problem is that with the BMW double line I’ll need to do one line and let it harden off before I can mask off to do the other.

I’ve also had the old girl out on the road for a run to see how things were.

I found that while she was willing to start and run, the start-up from cold was not as willing as it used to be and she was very reluctant to start from hot.

What I’ve done today is to treat her to a pair of new plugs, the old ones had been in for a long time now. I’ve also had the carburetters off and stripped and cleaned them, they have been standing for a couple of years and what fuel had been left in them had dried out and left a “varnish” of crud inside the passages and jets.

Fortunately she’s running on a pair Amal 276’s and these are an easy carb to strip down and clean.

I’ll need to synchronise the slide opening before I take her out again and while that’s a fiddly job it’s not that difficult.

I’ve also offered up the sidecar chassis to the bike, before I actually fit it I’m wanting to rig a sidecar brake. I had a sidecar brake on the Panther outfit and found it useful, after all the bikes brakes are from the 1930’s and brake technology has come a fair way since then so every little helps.

The rear brake on the R12 is with a heel operated pedal on the right-hand side. What I’m doing is to mount a pedal onto the sidecar chassis with a lever coming straight across to the bike and level with the rear brake pedal so its pad lies alongside the bike’s one. This means that when I apply the bike’s brake I’ll also apply the sidecar brake as well, and by rocking my foot I can vary their relative pressures.

However I’ll also be able to apply either brake on its own to give differential braking which can be useful to assist in cornering.

Only thing is that while I’ve the brake pedal set up I’ve still to arrange the cable fitment at the drum end of the system, as a “By The Way” the chassis I’m using is from an LS200 Steib. The wheel us from a Ural/Dneiper, a half width hub that looks in keeping with the R12 and the brake mechanism is an Enfield type from a rigid-framed Panther.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.